一区一精品-一区小说二区另类小说三区图-一区视频在线-一区免费视频-久久精品美女-久久精品毛片

Your location:Home > News > Company news
Company news

Working principle of aluminum foil rolling mill

AddTime:2020-12-10 10:00:11   Views:     【 Big Mid Small 】   Print   Close

     

The requirements for the plate shape accuracy of aluminum foil products are getting higher and higher. At the same time, with the market demand for products and the improvement of equipment design and manufacturing level, the aluminum foil rolling mill is also developing to a wider range, which makes the shape of aluminum foil more and more in the rolling process. The harder it is to control. Due to the negative roll gap rolling, the roll tilt and hydraulic bending have no obvious control effect on the shape of the roll. At the same time, due to the relationship between the work roll and the support roll diameter ratio and the wider roll surface, the bending control is for the middle of the roll. The mechanical convexity control is basically invalid. At this time, although the roll cooling control of the roll thermal crown can reduce the local deviation of the plate shape remaining in the first two controls, the response speed is slow, and the control effect is also weakened with the thickness reduction. To solve this problem, rolling mill designers and manufacturers at home and abroad have begun to use variable crown rolls (VC rolls) as backup rolls to eliminate the deviation of the parabolic shape of the plate and greatly improve the shape of the plate. Quality [4].

The VC roller is a combined support roller, which is assembled by a mandrel, a shaft sleeve and a rotary joint. There is a fluid chamber in the central area of ??the roller body between the mandrel and the shaft sleeve, which is filled with high-pressure oil with variable pressure. . The shaft sleeves at both ends of the roll neck are contracted, and the contraction joint is used as an external seal for the internal pressure oil and used for the free slip torque transmission of the roll drive. Its working principle is: the hydraulic oil in the high-pressure hydraulic station is sent to the expanding fluid chamber through the rotary joint through the hydraulic servo control to expand the shaft sleeve, and the uniform mechanical convexity is formed over the full length of the roll body to compensate for the roll produced during work Deflection. Because the VC roller diameter expansion has a linear relationship with the oil pressure in the cavity within a certain range, and can be steplessly adjusted, it can participate in the closed-loop shape control system.

Due to the different thickness of the strip, rolling mill rolling is a process of change from positive roll gap rolling to negative roll gap rolling. For control, it is also a process of combining multiple control methods, mainly including position control, pressure control, and pressure. Compensation control, AGC control, etc.

The speed setting of the rolling mill is set by the main operator on the main console in accordance with the process requirements, and is transmitted to the AGC via the Ethernet, and the AGC is then transmitted to the PLC and each transmission system. The speed setting is based on the main frame as the linear speed reference, and the given value of the speed is given by setting the diameter of the work roll and the reduction ratio of the reduction box. According to the control function, the speed setting has forward and reverse jog settings for fault handling; the threading speed setting is used for threading the rolling mill before production; the rolling line speed setting is used for normal rolling conditions. According to the principle of equal linear speed, it is distributed to each transmission system in the form of speed.

The coiling tension is generated by the dragging of the coiling motor to tighten the strip. Indirect tension control is adopted in the system, and the tension torque generated by the winding tension converted to the motor shaft is equal to the electromagnetic torque of the motor. Linear speed measurement is calculated by reading the pulse encoder on the deflector roller in front of the coiler by the speed regulating device, and is an important variable required for the calculation of the coil diameter.

Modern rolling mills perform full variable programming, and divide the system into rolling mill calibration designated application systems, drive serial port application systems, metering control application systems, thickness and flatness control application systems, and optimization application systems. These programs are processed by RDS (Real-time Data Server), and are used for sequencing roll force cylinders and roll bending control through the designated application system of rolling mill calibration. They are divided into rack calibration program, bounce calibration program, and stand safety monitoring program Etc.; Real-time monitoring of the running status of the rolling mill and the data transmitted by the drive and PLC through the drive serial port application system, and the data is stored in the RDS in order to maintain and optimally control the rolling mill.


Prev:Fire prevention measures in aluminum foil rolling process  Next:Basic composition of aluminum foil rolling mill

Back To Top
contact
  • ADD

    Development Zone, Zhuozhou City, Hebei Province

  • TEL

    +86-312-5522788

  • Follow WeChat

  • Enter mobile

Copyright ? Zhuozhou Feiya Machinery Co., Ltd.  http://m.92711.com.cn  All Rights Reserved   冀ICP備20012391號-1   Website designSANJIN  
主站蜘蛛池模板: wwww.黄| 国产成+人+亚洲+欧美+日韩| 国产日本欧美在线观看乱码| 亚洲免费在线观看视频| 人人鲁免费播放视频人人香蕉| 国产精品99久久久久久小说| 日本黄在线观看| 日韩在线网址| 亚洲欧美中文字幕高清在线一| a黄色片| 国产毛片网| 91国内精品线免费播放| 亚洲欧美一区二区三区不卡| 日韩黄视频| 亚洲国产黄色| 96视频在线| 国产一级片网站| jizz中国jizz日本老师水多| 久久亚洲国产成人影院| 国产精品冒白浆免费视频| 久久久久久久久久毛片精品美女 | 国产成人黄色| 国产高清国内精品福利99久久| 天天天操| 亚洲香蕉久久综合网| 国产成人在线精品| 三级在线观看国产| 暗黑破坏神3cg动画合集| 成人午夜视频免费| 午夜影院网页| 99九九影院理论片在线| 草草视频免费在线观看| 久久青草精品38国产免费| 日本精品在线| 成人亚洲欧美日韩中文字幕| 久久久国产视频| 欧美aaaav免费大片| 欧美日韩亚洲国产综合| 看西瓜视频| 国产综合久久一区二区三区| 日韩不卡在线|